Preface The Cisco Aironet Power Injector (AIR-PWRINJ5) increases wireless LAN deployment flexibility of Cisco Aironet Access Points by providing an alternative powering option to local power, inline power-capable multiport switches, and multiport power patch panels. The single-port Cisco Aironet Power Injector provides 802.3af power and data signal, sending both to the Cisco Aironet Access Point. The power injectors provide up to 15.4 W over the unused wire pairs of a Category 5 or better Ethernet cable, supplying enough power for a distance of 328 ft. (100 m) on the Cisco Aironet 1040, 1140, 1260, 2600, and 3500 Series Access Points.
While it can also support the Cisco Aironet Series 3600 Access Points when modules are not being used, it is recommended to use the AIR-PWRINJ4= power injector instead for the 3600 series, as it has sufficient power to supply to the AP and any installed modules. This guide covers the following Cisco Aironet Power Injector:. Cisco Aironet Power Injector (AIR-PWRINJ5). Cisco Aironet Power Injector The Cisco Aironet Power Injector provides both power and data to a connected Cisco Aironet Access Point. The device serves the following functions:. It provides Category 5 or better Ethernet media to the access point. It uses wires in an Ethernet cable to supply inline 15.4 W power to an access point.
The power injector provides an easy and economical way to provide data and power to an access point located in areas where power is not available. The power injector is used with the following Cisco Aironet Series Access Points:. 1040 series access points. 1140 series access points. 1260 series access points.
1600 series access points. 2600 series access points. 3500 series access points A Category 5 or better Ethernet cable connects the injector to a 10/100/1000 Ethernet switch, hub, or network, and another cable carries power and data to the access point's WAN Ethernet port. The power injector’s built-in power supply has a C14 connector that connects to a wall outlet or power strip.
The power injector connects to a wall outlet or power strip. 4 C14 Power Connector The Status LED indicates the following system status events:. AC Power - The LED blinks green at approximately 1.5 times per second to indicate that the Power Injector is powered ON and ready for connection.
AP Power - The LED lights solid green to indicate that a valid IEEE 802.3af load (AP) is detected and powered ON. Invalid load connected or Fault: The LED rapidly blinks green at 10 times per second to an invalid load connected or a Fault.
In these conditions the AP has not been powered on. This occurs for 2 seconds for normal error delay, and the detection process will automatically start again after 2.2 seconds unless there is a “restart after disconnect condition” set during the initial configuration. Shows a typical installation scenario. Figure 2 Power Injector AIR-PWRINJ5 Installation Scenario. Installing the Power Injector Follow these steps to install the power injector: 1. Plug a Category-5 Ethernet cable into the port on the power injector labeled AP. Plug the other end of the Ethernet cable into the WAN uplink Ethernet port of the access point.
Plug a Category-5 Ethernet cable into the port on the power injector labeled Switch. Plug the other end of the Ethernet cable into your 10/100/1000 Ethernet switch, hub, or network. When power is applied, the Status LED blinks green at approximately 1.5 times per second. When the AP is detected, the Status LED glows solid green. If the power injector is connected incorrectly, the Status LED blinks green at 10 times per second. Secure the power injector by mounting it to a vertical or horizontal surface using the mounting keyholes on the bottom of the unit.
Using the Mounting Tabs To mount the power injector to a vertical or horizontal surface using the mounting tabs, you will need the following parts and tools:. Two #6 plastic wall anchors if mounting to a drywall surface. Two #6 x 1-in.
(2.5 cm) sheet-metal screws. A drill and a 3/16-in (0.48-cm) drill bit. A Phillips head screw driver. A small hammer Follow these steps to mount the power injector: 1. Using the holes in the power injector mounting tabs as a template, mark the locations on the surface where you will drill the holes for the wall anchors or screws.
Drill a 3/16-in. (4.7-mm) hole at each marked location.
If you are using #6 wall anchors, use a hammer to install them in the holes. Hold the power injector to the wall and align the mounting tabs on the power injector with the screw holes. Insert the #6 screws through the mounting tabs and into the holes in the wall or surface. Use a Phillips head screwdriver to drive the screws into the surface.
Regulatory Information The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:.
Turn the television or radio antenna until the interference stops. Move the equipment to one side or the other of the television or radio. Move the equipment farther away from the television or radio. Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. Could void the FCC approval and negate your authority to operate the product.
Preface Table Of Contents Preface The Cisco Aironet Power Injector products increase wireless LAN deployment flexibility of Cisco Aironet Access Points and Bridges by providing an alternative powering option to local power, inline power-capable multiport switches, and multiport power patch panels. The single-port Cisco Aironet Power Injector combines 48-VDC power (supplied by the external power supply) with the data signal, sending both to the Cisco Aironet Access Point or Bridge. The Cisco Aironet Power Injector Media Converter converts fiber media signals to Category 5 Ethernet media and combines the data signal with power for delivery to the access point or bridge. The power injector accepts 48-VDC power from either the barrel connector of the local power supply or an alternative 48-VDC power source. The power injectors provide up to 15 W (depending on the Cisco power supply model) over the unused wire pairs of a Category 5 Ethernet cable, supplying enough power for a distance of 328 ft. (100 m) on the Cisco Aironet 350, 1100, 1200 Series Access Points and the Cisco Aironet 350 Series Bridges.
This guide covers the following Cisco Aironet Power Injectors:. Cisco Aironet Power Injector Media Converter (AIR-PWRINJ-FIB). Cisco Aironet Power Injector (AIR-PWRINJ3) Cisco Aironet Power Injector Media Converter The Cisco Aironet Power Injector Media Converter provides both power and data to a connected Cisco Aironet Access Point. The device provides the following functions:. Converts fiber media to Category 5 Ethernet media. Uses the unused wires in an Ethernet cable to supply inline 48-VDC power to the access point The power injector media converter is ideal for incorporating an access point into a fiber-optic network and can be used with 350, 1100, and 1200 series access points and 350 series bridges. The power injector media converter receives data over the fiber-optic network through its MT-RJ fiber connector.
The fiber-optic data signals are converted to Ethernet data signals and sent to the access point through the injector's Category 5 RJ-45 port. A Category 5 Ethernet cable connects the injector to the access point. The injector's power supply connects to a wall outlet or power strip to supply the power.
An alternate 48-VDC power source can be used instead of the power supply. The power injector media converter can be mounted on most horizontal and vertical surfaces.
To avoid overheating and possible failure, do not stack or tie together (bundle) the power injector and its AC power adapter. Cisco Aironet Power Injector The Cisco Aironet Power Injector provides both power and data to a connected access point or bridge. The device serves the following functions:. It provides Category 5 Ethernet media to the access point or bridge. It uses the unused wires in an Ethernet cable to supply inline 48-VDC power to an access point or bridge.
The power injector provides an easy and economical way to provide data and power to an access point or bridge located in areas where power is not available. The power injector is used with the following Cisco Aironet wireless products:. 350 series access points and bridges.
1100 series access points. 1200 series access points A Category 5 Ethernet cable connects the power injector to a 10/100 Ethernet switch, hub, or network, and another cable carries power and data to the access point's or bridge's Ethernet port. The power injector's power supply connects to a wall outlet or power strip. The power injector can be mounted on most horizontal and vertical surfaces.
To avoid overheating and possible failure, do not stack or tie together (bundle) the power injector and its AC power adapter. The following illustration shows the key features of the power injector. Unpacking the Power Injector The following items are shipped with both models of the power injector:. Category 5 Ethernet cable. This installation guide. Electrical tie-wrap with screw mount hole, wall anchor, and screw If any item is missing or damaged, contact your Cisco representative or reseller.
Additional Requirements Use the power supply that shipped with your access point to supply 48-VDC power for the injector. If you install the access point or bridge in an environmental air space such as above a suspended ceiling, check national and local safety codes to make sure that the Ethernet cable you connect to the unit meets applicable standards. Release notes for these products are on Cisco.com.
Browse to the following page. Note The maximum distance that is supported for in-line power is 328 ft. (100 m), including the length of the 6.5-ft. (2-m) Ethernet cable provided with both power injector models. Installing the Power Injector Media Converter Follow these steps to install the power injector media converter: 1. Plug a Category 5 Ethernet cable into the port on the media converter labeled 100 Base Tx To Device. Plug the other end of the Ethernet cable into the Ethernet Port on the access point.
Plug the fiber-optic network cable to the port on the media converter labeled 100 Base Fx To Network. Plug the other end of the cable to the fiber-optic source. Connect a suitable 48-VDC power source, such as the power pack that shipped with your access point or the power supply pigtail option, to the power receptacle labeled DC48V. Secure the 48-VDC power cord in the retaining clips on the power injector as shown in the following illustration. 3 Power cord retaining clips 7. Secure the media converter by mounting it to a vertical or horizontal surface using the supplied tie wrap mounting kit or using the keyhole mounting holes on the back of the unit.
To avoid overheating and possible failure, do not stack or tie together (bundle) the power injector and its AC power adapter. When power is applied to the power injector media converter, the Power LED glows green. When a device is discovered, the Status LED glows green continuously. Installing the Power Injector Follow these steps to install the power injector: 1. Plug a Category-5 Ethernet cable into the port on the power injector labeled 10/ 100Base Tx to Device. Plug the other end of the Ethernet cable into the Ethernet Port on the access point or bridge.
Plug a Category-5 Ethernet cable into the port on the power injector labeled 10/100 Base Tx to Network. Plug the other end of the Ethernet cable into your 10/100 Ethernet switch, hub, or network. Connect a suitable 48-VDC power source to the power receptacle labeled DC48V. To avoid overheating and possible failure, do not stack or tie together (bundle) the power injector and its AC power adapter. When power is applied, the Power LED glows green. The Device Status LED is dark until a device is discovered and then it glows green. If the power injector is not connected to a device capable of receiving inline power, or if it is connected incorrectly, the Power LED glows amber continuously.
Secure the power injector by mounting it to a vertical or horizontal surface using the supplied tie wrap mounting kit or using the keyhole mounting holes on the back of the unit. Mounting Instructions You can mount both models to most vertical or horizontal surfaces using the supplied tie wrap mounting kit. If you need a more secure mounting method, you can also use the mounting keyholes on the bottom of the unit. Using the Tie Wrap Mounting Kit The supplied tie wrap mounting kit consists of the following parts:. A plastic tie wrap. A #10 wall anchor and #10 screw. An adhesive-backed plastic mounting plate Follow these steps to mount the power injector with the supplied tie wrap mounting kit.
It may be helpful to refer to the illustration on page 11. Mark the position on the surface where you want to mount the power injector.
To mount the power injector using the wall anchor and screw, follow the steps below. If you are using the plastic mounting bracket, go to Step 3.
Drill a 5/32-in. (4-mm) hole at the location you marked. Install the #10 wall anchor in the hole. Insert the #10 screw into the hole of the tie wrap and into the wall anchor. Tighten the screw just enough to keep it secure in the wall anchor. Slide the end of the tie wrap into the tie wrap mounting slot on the back of the power injector. Insert the end of the tie wrap into its locking slot and cinch it up.
Use a Phillips head screw driver to tighten the screw into the wall anchor. Follow these steps to mount the power injector using the plastic mounting plate: a. The mounting plate has an adhesive back, so make sure the surface on which you intend to mount the plate is clean. Remove the protective tape from the mounting plate to expose the adhesive backing. Press and hold the plate to make sure the plate adheres to the surface.
Note You can also install the plate using two #10 screws, or you can use the screws to augment the adhesive backing. Thread the plastic tie wrap through the slot in the mounting plate and then into the tie wrap mounting slot on the back of the power injector. Insert the tie wrap into its locking slot and cinch it up.
Air-pwrinj4 Installation Guide Free
Using the Keyhole Mounting Holes To mount the power injector to a vertical or horizontal surface using the keyhole mounting holes, you will need the following parts and tools:. Two #6 plastic wall anchors.
Two #6 x 1-in. (2.5 cm) sheet-metal screws. A drill and a 3/16-in (0.48-cm) drill bit. A Phillips head screw driver. A small hammer Follow these steps to mount the power injector: 1. Mark the locations on the surface where you will drill the holes for the wall anchors or screws. Note Make sure the holes are spaced 3 1/8 in.
(7.94 cm) apart. Drill a 3/16-in.
(4.7-mm) hole at each marked location. If you are using #6 wall anchors, use a hammer to install them in the holes. Start the #6 screws into the wall anchors (or the surface). Use a Phillips head screwdriver to drive the screws into the wall anchors (or surface) until there is a gap of approximately ¼ in. (0.6 cm) between the surface and the screw heads. Line up the large end of the keyholes on the power injector with the screws.
Insert the power injector into the keyhole and slide it down into the small end of the keyhole. Power Injector (AIR-PWRINJ3) Dimensions 5.4 in. (13.7 cm x 5.3 cm x 3.3 cm) Stacking restrictions Do not stack. Do not bundle the power injector and AC power adapter.
Do not stack. Do not bundle the power injector and AC power adapter. Regulatory Information The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco's installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco's written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. You can determine whether your equipment is causing interference by turning it off.
If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:.
Turn the television or radio antenna until the interference stops. Move the equipment to one side or the other of the television or radio. Move the equipment farther away from the television or radio.
Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. Could void the FCC approval and negate your authority to operate the product. Applicable Standards Except where indicated, both models meet the following standards:. FCC Part 15.107 and 15.109 Class B. ICES-003 Class B (Canada).
AS/NZS 3548 Class B. VCCI Class B. EN 301.489-1 and 17.
EN 55022. EN 55024. EN 60950. UL 60950. CSA C22.2 No. 60950.
IEC 60825 (power injector media converter). IEC 60950. UL 2043 (power injector media converter).
While it can also support the Cisco Aironet Series 3600 Access Points when modules are not being used, it is recommended to use the AIR-PWRINJ4= power injector instead for the 3600 series, as it has sufficient power to supply to the AP and any installed modules. This guide covers the following Cisco Aironet Power Injector:. Cisco Aironet Power Injector (AIR-PWRINJ5). Cisco Aironet Power Injector The Cisco Aironet Power Injector provides both power and data to a connected Cisco Aironet Access Point. The device serves the following functions:.
It provides Category 5 or better Ethernet media to the access point. It uses wires in an Ethernet cable to supply inline 15.4 W power to an access point. The power injector provides an easy and economical way to provide data and power to an access point located in areas where power is not available. The power injector is used with the following Cisco Aironet Series Access Points:. 1040 series access points.
1140 series access points. 1260 series access points. 1600 series access points. 2600 series access points. 3500 series access points A Category 5 or better Ethernet cable connects the injector to a 10/100/1000 Ethernet switch, hub, or network, and another cable carries power and data to the access point's WAN Ethernet port.
The power injector’s built-in power supply has a C14 connector that connects to a wall outlet or power strip. The power injector connects to a wall outlet or power strip. 4 C14 Power Connector The Status LED indicates the following system status events:. AC Power - The LED blinks green at approximately 1.5 times per second to indicate that the Power Injector is powered ON and ready for connection. AP Power - The LED lights solid green to indicate that a valid IEEE 802.3af load (AP) is detected and powered ON. Invalid load connected or Fault: The LED rapidly blinks green at 10 times per second to an invalid load connected or a Fault.
In these conditions the AP has not been powered on. This occurs for 2 seconds for normal error delay, and the detection process will automatically start again after 2.2 seconds unless there is a “restart after disconnect condition” set during the initial configuration. Shows a typical installation scenario. Figure 2 Power Injector AIR-PWRINJ5 Installation Scenario.
Installing the Power Injector Follow these steps to install the power injector: 1. Plug a Category-5 Ethernet cable into the port on the power injector labeled AP.
Plug the other end of the Ethernet cable into the WAN uplink Ethernet port of the access point. Plug a Category-5 Ethernet cable into the port on the power injector labeled Switch. Plug the other end of the Ethernet cable into your 10/100/1000 Ethernet switch, hub, or network. When power is applied, the Status LED blinks green at approximately 1.5 times per second. When the AP is detected, the Status LED glows solid green.
If the power injector is connected incorrectly, the Status LED blinks green at 10 times per second. Secure the power injector by mounting it to a vertical or horizontal surface using the mounting keyholes on the bottom of the unit. Using the Mounting Tabs To mount the power injector to a vertical or horizontal surface using the mounting tabs, you will need the following parts and tools:. Two #6 plastic wall anchors if mounting to a drywall surface. Two #6 x 1-in. (2.5 cm) sheet-metal screws. A drill and a 3/16-in (0.48-cm) drill bit.
A Phillips head screw driver. A small hammer Follow these steps to mount the power injector: 1. Using the holes in the power injector mounting tabs as a template, mark the locations on the surface where you will drill the holes for the wall anchors or screws.
Drill a 3/16-in. (4.7-mm) hole at each marked location. If you are using #6 wall anchors, use a hammer to install them in the holes. Hold the power injector to the wall and align the mounting tabs on the power injector with the screw holes.
Insert the #6 screws through the mounting tabs and into the holes in the wall or surface. Use a Phillips head screwdriver to drive the screws into the surface. Regulatory Information The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy.
If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules.
These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices.
If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:. Turn the television or radio antenna until the interference stops. Move the equipment to one side or the other of the television or radio. Move the equipment farther away from the television or radio.
Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. Could void the FCC approval and negate your authority to operate the product.
Likes 0 Downloads 0 Summary of Contents of installation guide for Cisco Cisco Aironet 1250 Series Access Point. Read This First This guide is designed to help you prepare your Cisco Aironet 1250 Series Access Point (hereafter referred. Step 1 Grasp the access point with both hands as shown in the illustration below. 231161 2 78-17831-01. Sentinel usb dongle emulator.
Step 2 With your right thumb or forefinger, pull the security hasp toward you to release it from the mounting. Before You Start Because the configuration process varies depending on how you intend to use your access point, detailed configuration.
These documents are also available on cisco.com. Follow this link: home.html Make sure that you are using a computer. Safety Information The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to.
Warning Read the installation instructions before you connect the system to its power source. Statement 1004 Warning This product relies. Unpacking the Access Point Package Contents Each access point package contains the following items:. Cisco Aironet 1250 series autonomous. Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping. Before Beginning the Installation Before you begin the installation, refer to the illustrations on the following pages to become familiar.
1 2 6 ETHERNET STATUS RADIO 3 4 230553 5 1 2.4-GHz radio antennas 4 5-GHz radio antennas 2 2.4-GHz. This illustration shows LED placement. ETHERNET STATUS RADIO 230563 ETHERNET STATUS RADIO 1-01. This illustration shows the bottom of the access point with the mounting plate removed. 48vDC ETHERNET CONSOLE MODE 170127 1.
This illustration shows the connections inside the Ethernet and console port bays. CAUTION EXTERNAL DC AND INLINE PoE POWER SOURCE. Installation Summary Installing the access point involves these operations:. Mounting the Access Point. Connecting Power.
Obtaining and. Note The 1250 series power injector, 1250 series DC power module, and antennas are not tested to UL 2043 and.
– An IEEE 802.3af compliant Cisco inline power switch – A Cisco 1250 series power injector (AIR-PWRINJ4) Note Some. Note If your access point is connected to in-line power, do not connect the power module to the access point. – Provide your organization’s network administrator with your access point MAC address. Your network administrator will query the DHCP. Assigning an IP Address Using the CLI When you assign an IP address to the access point using the CLI. Option 1 Switch (with or without inline power) SYST RPS 1 2 3 4 STAT UTIL DUPLX 5 SPEED.
The access point power options:. Option 1—Switches with sufficient inline power (single radio only): – An inline power capable. Connecting to an Ethernet Network with an Inline Power Source Caution Be careful when handling the access point; the bottom.
– A switch with inline power. – The Ethernet connector on the 1250 series power injector labeled To AP. Follow these steps to connect the access point to an Ethernet LAN when you are using a local power source. The following basic settings must be configured on your access point.
Host Name. Configuration Server Protocol. IP.
Basic security settings are explained in the “Configuring the Access Point for the First Time” chapter of the Cisco IOS. In Case of Difficulty If you followed the instructions in previous sections of this guide, you should have had no. Note Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from.
Ethernet LED Radio LED Status LED Meaning Red – Red Ethernet failure Amber – Blinking Configuration recovery in blue progress. Resetting to Default Configuration Note These steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP.
Step 4 Continue holding the MODE button until the Ethernet LED turns amber (approximately 2 to 3 seconds), then release. Step 7 Click the Reset to Defaults or Reset to Defaults (Except IP) button (depending on your configuration).
Cisco 90-Day Limited Hardware Warranty Terms There are special terms applicable to your hardware warranty and various services that you. Read the document online, or click the PDF icon to download and print the document in Adobe Portable.
Replacement, Repair, or Refund Policy for Hardware Cisco or its service center will use commercially reasonable efforts to ship a.
Spec Interface Ethernet Port LEDs 2 - Power Status Device Connectivity Ports LAN Connection: 10/100BASE-TX To Network Device Connection:10/100BASE-TX To Device Power Input 48VDC ± 10%, 18 watts Dimensions 5.5' x 2.1' x 1.4' Weight 4 oz. Temperature 0°C - 45°C (32°F - 113°F) Humidity 10% - 90%, Non-Condensing Features Features CISCO Aironet Power Injector for 1100, 1130AG, 1200, 1230AG and 1240AG Series Power Supply Requirements: CISCO Aironet power supply, 48 VDC ± 5%, 18 watts Interlockable: Yes Device Connection: Max Cat 5 cable length: 100 m from switch to device LAN Connection: Max Cat 5 cable length: 100 m from switch to device.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |